Direct Current (DC)

Direct Current, electrical current that flows in one direction only. In wikipedia it's defined as:

Direct Current (DC or "continuous current") is the constant flow of electric charge. This is typically in a conductor such as a wire, but can also be through semiconductors, insulators, or even through a vacuum as in electron or ion beams. In direct current, the electric charges flow in the same direction, distinguishing it from alternating current (AC). A term formerly used for direct current was Galvanic current.

The first commercial electric power transmission (developed by Thomas Edison in the late 19th century) used direct current. Because of the advantage of alternating current over direct current in transforming and transmission, electric power distribution today is nearly all alternating current. For applications requiring direct current, such as third rail power systems, alternating current is distributed to a substation, which utilizes a rectifier to convert the power to direct current.

Types of Direct Current

Within electrical engineering, the term DC is a synonym for "constant". For example, the voltage across a DC voltage source is constant as is the current through a DC current source. The DC solution of an electric circuit is the solution where all voltages and currents are constant. It can be shown that any voltage or current waveform can be decomposed into a sum of a DC component and a time-varying component. The DC component is defined to be the average value of the voltage or current over all time. The average value of the time-varying component is zero.

Although DC stands for "Direct Current", DC sometimes refers to "constant polarity." With this definition, DC voltages can vary in time, such as the raw output of a rectifier or the fluctuating voice signal on a telephone line.

Some forms of DC (such as that produced by a voltage regulator) have almost no variations in voltage, but may still have variations in output power and current.

Direct current installations usually have different types of sockets, switches, and fixtures, mostly due to the low voltages used, from those suitable for alternating current. It is usually important with a direct current appliance not to reverse polarity unless the device has a diode bridge to correct for this. (Most battery-powered devices do not.)

High voltage direct current is used for long-distance point-to-point power transmission and for submarine cables, with voltages from a few kilovolts to approximately one megavolt.

DC is commonly found in many low-voltage applications, especially where these are powered by batteries, which can produce only DC, or solar power systems, since solar cells can produce only DC. Most automotive applications use DC, although the alternator is an AC device which uses a rectifier to produce DC. Most electronic circuits require a DC power supply. Applications using fuel cells (mixing hydrogen and oxygen together with a catalyst to produce electricity and water as byproducts) also produce only DC.

Most telephones connect to a twisted pair of wires, and internally separate the AC component of the voltage between the two wires (the audio signal) from the DC component of the voltage between the two wires (used to power the phone).

Telephone exchange communication equipment, such as DSLAM, uses standard -48V DC power supply. The negative polarity is achieved by grounding the positive terminal of power supply system and the battery bank. This is done to prevent electrolysis depositions.

An electrified third rail can be used to power both underground (subway) and overground trains.


The Difference with AC (Alternate Current)

In 1887 direct current (DC) was king. At that time there were 121 Edison power stations scattered across the United States delivering DC electricity to its customers. But DC had a great limitation -- namely, that power plants could only send DC electricity about a mile before the electricity began to lose power. So when George Westinghouse introduced his system based on high-voltage alternating current (AC), which could carry electricity hundreds of miles with little loss of power, people naturally took notice. A "battle of the currents" ensued. In the end, Westinghouse's AC prevailed.

This special feature isn't about the two electrical systems and how they worked. Rather, it's a simple explanation that shows the difference between AC and DC.

To find out more about alternating and direct current, what exactly an electric current is, and two ways that the currents can be produced, check out the interaction by clicking on checkboxes below, and see the current flows on the right illustration...

 All Off
 Alternate Current (AC)
 Direct Current (DC)

Source: Wikipedia, Microsoft Encarta, and other electricity resource.